Skip to content Skip to sidebar Skip to footer

Casing Wear in Directional Drilling: How to Protect Well Integrity Before Damage Occurs 

A casing string may meet its original design requirements and still experience mechanical damage during subsequent drilling operations. 

In directional and extended-reach wells, the rotating drillstring can contact the inside of previously installed casing. Over time, this contact may remove casing material, reducing wall thickness and potentially affecting pressure integrity. 

The challenge is that casing wear can develop progressively, without an obvious indication at the surface. 

Casing wear analysis helps drilling engineers identify where contact is most likely, estimate potential wall loss, and determine whether the remaining casing can meet its required design loads. 

For operators drilling complex well trajectories, understanding casing wear is an important part of protecting well integrity. 

What Is Casing Wear in Directional Drilling? 

Casing wear is the progressive removal of material from the inner surface of casing due to mechanical contact with drillstring components. 

During drilling, tool joints and sections of drill pipe may contact the casing as the drillstring rotates, slides, or moves axially. 

The risk is particularly important in directional wells because changes in wellbore curvature can increase contact forces between the drillstring and casing. 

Research published in the Journal of Petroleum Science and Engineering identifies severe doglegs as locations where drillstring contact can produce substantial casing wear. 

However, wear severity is not determined by trajectory alone. It also depends on contact forces, operating conditions, materials, drilling fluid properties, and cumulative exposure. 

What Does Published Industry Research Show? 

A 2022 peer-reviewed experimental study titled Casing Wear and Wear Factors: New Experimental Study and Analysis investigated casing wear using actual drill pipe joints and P110 casing samples. 

Researchers tested two side loads, 1,000 N and 1,400 N, and two rotational speeds, 115 and 207 rpm, under different lubrication conditions. 

The study reported that, under the same tested conditions: 

  • Wear volume and wear factor under water-based fluid lubrication were more than twice those measured under oil-based fluid lubrication. 
  • Dry contact produced the highest wear volume and wear factor. 
  • Increasing the normal load at constant rotational speed increased the wear factor. 

These findings demonstrate that casing wear depends on several interacting variables rather than a single drilling parameter. 

Importantly, the laboratory results should not be interpreted as evidence that water-based drilling fluids universally cause twice as much casing wear in field operations. 

Actual outcomes depend on fluid formulation, casing material, tool joint characteristics, contact forces, and operating conditions. 

Source: Materials (2022), “Casing Wear and Wear Factors: New Experimental Study and Analysis.” 

Why Is Casing Wear a Problem? 

Casing provides structural support and forms part of the well’s pressure containment system. 

When mechanical wear reduces casing wall thickness, the remaining material may have less capacity to withstand certain loads. 

Potential consequences include: 

  • Reduced resistance to internal pressure. 
  • Changes in collapse and combined-load performance. 
  • Localized stress concentrations. 
  • Additional casing inspection or integrity assessment requirements. 
  • Restrictions on future drilling or completion operations. 

A 2020 study published in Science Progress examined casing wear depth and residual strength in highly deviated wells. 

The researchers emphasized the importance of evaluating remaining casing strength after material loss rather than considering wear depth alone. 

This distinction matters because the acceptability of a worn casing section depends on the loads it must withstand. 

What Causes Excessive Casing Wear? 

1. High dogleg severity 

Dogleg severity describes the rate of change in wellbore direction. 

In sections with significant curvature, drillstring components may experience increased contact with the casing wall. 

These contact forces can contribute to localized wear, particularly when rotation continues over extended periods. 

2. Drillstring side force 

Side force is an important input in casing wear prediction. 

It is influenced by well trajectory, drillstring tension, equipment configuration, and operating conditions. 

Higher contact loading can increase wear under otherwise comparable conditions. 

3. Rotational exposure 

Cumulative drillstring rotation influences the amount of sliding contact between tool joints and casing. 

However, rotational speed and wear do not always have a simple linear relationship. 

Laboratory studies show that lubrication regimes and wear mechanisms can change with rotational speed. 

4. Tool joint and hardbanding characteristics 

Tool joints may have different surface properties from the drill pipe body. 

Their dimensions, materials, hardbanding condition, and surface characteristics can influence casing wear. 

Equipment compatibility should therefore be considered during engineering reviews. 

5. Drilling fluid properties 

Drilling fluids influence lubrication and friction at contacting surfaces. 

Wear behavior can vary with fluid type, additives, solids content, and operating conditions. 

Fluid selection should consider the overall drilling requirements rather than casing wear performance in isolation. 

How Can Drilling Engineers Predict Casing Wear? 

Casing wear prediction generally combines well geometry, drillstring mechanics, operational parameters, and experimentally or historically derived wear factors. 

A typical engineering workflow evaluates: 

Well trajectory: Identify sections with elevated dogleg severity or significant drillstring contact. 

Torque and drag: Estimate the forces acting between the drillstring and casing. 

Operating conditions: Consider rotation, drilling duration, equipment configuration, and anticipated drilling activities. 

Wear factors: Apply values appropriate to the materials and operating conditions, recognizing the uncertainty associated with these inputs. 

Remaining casing strength: Evaluate whether predicted material loss affects the casing’s ability to satisfy required design loads. 

A 2023 study published in Upstream Oil and Gas Technology demonstrated a casing wear prediction method incorporating mud logging data. 

The researchers calculated drillstring contact forces and estimated wear volume and groove depth, then compared their predictions with wireline measurements from a well in southwestern Iran. 

This provides an example of how operational data can support more informed casing wear assessments. 

How Can Operators Reduce Casing Wear Risk? 

1. Evaluate high-risk sections before drilling 

Identify planned intervals where drillstring contact forces may be elevated. 

Trajectory and torque-and-drag analysis can help determine where additional wear assessment is warranted. 

2. Review the planned drilling parameters 

Assess how anticipated operating conditions contribute to cumulative contact and wear. 

Changes to operating parameters should be evaluated against drilling performance, hole cleaning, equipment limitations, and other operational requirements. 

3. Consider drillstring and tool joint compatibility 

Review tool joint dimensions, hardbanding characteristics, and other relevant equipment properties. 

Appropriate component selection may help manage casing contact and wear. 

4. Use representative wear factors 

Wear prediction is sensitive to the wear factors used in the model. 

Values should reflect relevant materials, fluid systems, and operating conditions wherever reliable data are available. 

5. Monitor cumulative exposure 

Track operating activities that contribute to casing contact, particularly in high-risk intervals. 

A 2024 Society of Petroleum Engineers paper on integrated casing wear management recommends monitoring actual wellbore tortuosity, dogleg severity, drillstring revolutions, and relevant wear indicators during drilling. 

6. Verify casing condition when required 

Predictions should be compared with actual measurements when inspection is necessary and practical. 

Electromagnetic and ultrasonic inspection technologies can provide information about casing condition, including wall thickness and wear. 

The appropriate inspection method depends on casing configuration, well conditions, and the required evaluation. 

Why Casing Wear Prediction Should Be Connected to Casing Design 

Predicting casing wall loss is only part of the engineering problem. 

The more important question is whether the casing will retain sufficient strength throughout its intended service life. 

For example, a localized reduction in wall thickness may affect the casing’s ability to withstand internal pressure or external loading. 

The engineering assessment should consider the location and geometry of the wear, remaining wall thickness, material properties, and applicable load cases. 

A casing section should not be considered acceptable simply because the predicted percentage of wear is below an arbitrary threshold. 

Acceptance criteria must be based on the relevant casing design requirements and operating conditions. 

How BOAX Drilling Solutions Can Help 

Managing casing wear requires an understanding of how well trajectory, drillstring mechanics, operating parameters, and casing design interact. 

BOAX Drilling Solutions provides an engineering-focused perspective on drilling challenges and operational performance. 

Within an appropriately defined project scope, drilling engineering support can help operators review potential wear exposure, evaluate relevant operating constraints, and identify where specialized casing wear modeling or integrity assessment may be needed. 

This approach supports better coordination between drilling engineering, well design, and operational decision-making. 

The objective is to identify potential casing integrity concerns before they develop into more difficult operational problems. 

Specialized casing wear prediction, inspection, and remaining-strength verification should be performed using qualified personnel, validated methods, and suitable engineering tools. 

Conclusion: Protecting Casing Integrity Requires More Than Initial Design 

Casing wear is a cumulative engineering challenge that can affect directional, horizontal, and extended-reach drilling operations. 

Published research demonstrates that contact loading, lubrication, rotational exposure, and well geometry all influence wear behavior. 

Effective management therefore requires more than selecting a casing grade or monitoring a single drilling parameter. 

By evaluating high-risk intervals, using appropriate wear prediction methods, and verifying remaining casing strength where necessary, drilling teams can make better-informed decisions about casing integrity. 

Planning a directional or extended-reach well with challenging drilling conditions? 

Explore how BOAX Drilling Solutions can support your drilling engineering and well construction objectives. 

References 

  1. Yu, H., Taleghani, A. D., and Lian, Z. (2018). “Modelling Casing Wear at Doglegs by Incorporating Alternate Accumulative Wear.” Journal of Petroleum Science and Engineering, 168, 273–282. 
    https://doi.org/10.1016/j.petrol.2018.05.009 
  1. “Casing Wear and Wear Factors: New Experimental Study and Analysis.” (2022). Materials, 15(19), 6544. 
    https://doi.org/10.3390/ma15196544 
  1. Ding, L., Xian, M., and Zhang, Q. (2020). “Prediction of Casing Wear Depth and Residual Strength in Highly-Deviated Wells Based on Modeling and Simulation.” Science Progress. 
    https://doi.org/10.1177/0036850420969577 
  1. Farab, A. E., et al. (2023). “A New Method for Predicting Casing Wear in Highly Deviated Wells Using Mud Logging Data.” Upstream Oil and Gas Technology. 
    https://doi.org/10.1016/j.upstre.2023.100094 
  1. Society of Petroleum Engineers (2024). “Integrated Casing Wear Management in Well Design and Drilling Operations with a Field Case Analysis.” SPE Asia Pacific Oil and Gas Conference and Exhibition. 
    https://onepetro.org/SPEAPOG/proceedings-abstract/24APOG/24APOG/D021S018R007/570327 
  1. SLB. “Well Integrity Evaluation.” 
    https://www.slb.com/products-and-services/innovating-in-oil-and-gas/reservoir-characterization/reservoir-testing/well-integrity-evaluation 

Leave a comment